Dell 1400 Manual do Proprietário

Dell Storage MD1400 EnclosuresHardware Owner's Manual

Power indicator codesFigure 6. Power indicator codesItem LED Icon Color State1 DC power Green• ON — Normal operation. Power supply is connected to DC

• The OpenManage Server Administrator documentation provides information about managing your storage solution using the storage management service wit

2Installing enclosure componentsRecommended toolsYou may need the following items to perform the procedures in this section:• Key to the system keyloc

Installing the front bezel1. Hook the right end of the bezel onto the chassis.2. Fit the free end of the bezel onto the system.3. Secure the bezel wit

Figure 8. Removing and installing a 3.5-inch hard disk drive blank1. hard disk drive blank 2. release tabInstalling a hard disk drive blank1. If insta

Figure 9. Removing and installing a hard disk drive1. release button 2. hard disk drive3. hard disk drive carrier handleInstalling a hard disk driveCA

Figure 10. Removing and installing a hard drive into a 3.5-inch hard disk drive carrier1. screws (4) 2. hard disk drive3. hard disk drive carrierInsta

Removing an EMM blankCAUTION: To maintain proper system cooling, make sure you install an EMM blank in the empty slot.1. Remove EMM 0. See Removing an

NOTE: Stacking the EMM will damage the sensitive EMI contactsFigure 12. Removing and installing an EMM1. release lever 2. EMM3. release tabInstalling

AC power supply unit or cooling fan moduleYour enclosure supports two hot-swappable power supply unit or cooling fan modules. While the enclosure can

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

Installing an AC power supply unit or cooling fan module1. Slide the power supply unit or cooling fan module into the chassis until the release tab cl

Figure 15. Power indicator codesItem LED Color State1 Power outputGreen• ON — Normal operation. Power supply is connected to DC power and the power sw

DC power supply module back panel featuresFigure 16. DC power supply module back panel featuresItem Feature Description1 Power supply release leverUnl

Required Wires• One UL 4 AWG, 2 m maximum (stranded) black wire [–(48–60) V DC]• One UL 4 AWG, 2 m maximum (stranded) red wire (V DC return)• One UL 4

Wiring the power cablesWARNING: For equipment using –(48–60) V DC power supplies, a qualified electrician must perform all connections to DC power and

Figure 19. Connecting the dc power cables1. attached (trapped) finger screws 2. connector on the power supply cable 3. connector on the power supply m

Figure 20. Removing and installing a dc power supply module1. release latch 2. power supply module3. power supply module handleInstalling a DC Power S

NOTE: The line input LED lights up when the power cable is connected, even if the switches on the power supply modules are off.NOTE: When installing,

Technical specificationsNOTE: The following specifications are only those required by law to ship with your system. For a complete and current listing

Figure 21. Removing and installing the control panel1. control panel 2. chassis3. release tabInstalling the control panel1. Align the control panel wi

Contents1 About your enclosure...5Front-panel features and ind

3. Remove the hard disk drives. See Removing a hard disk drive.4. Remove the EMMs. See Removing an EMM.5. Remove the power supply or cooling fan modul

Figure 23. Removing and installing the backplane1. screws (5) 2. captive screws (2)3. backplaneInstalling the backplane1. Align the holes on the backp

3Troubleshooting your enclosureSafety first—for you and your enclosureCAUTION: Many repairs may only be done by a certified service technician. You sh

• If the AC power LED is not lit, check the power cord and power source into which the power supply is plugged.– Connect another device to the power s

Troubleshooting Enclosure Management ModulesCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubles

6. Ensure that all the cables are attached correctly according to the enclosure mode you selected. For more information about enclosure modes, see Del

• Hard disk drives• EMMs• Power supply unit or cooling fan modules• Control panel• Backplane2. Ensure that all the cables are properly connected and t

4Getting helpContacting DellNOTE: Dell provides several online and telephone-based support and service options. If you do not have an active Internet

Installing the control panel... 29Backplane...

1About your enclosureFront-panel features and indicatorsFigure 1. Front-panel features and indicatorsItem Indicator, Button, or ConnectorIcon Descript

Front-bezel features and indicatorsFigure 2. Front-bezel features and indicatorsItem Indicator, Button, or ConnectorIcon Description1 Enclosure status

Hard disk drive indicator patternsFigure 3. Hard disk drive indicators1. hard disk drive activity indicator (green) 2. hard disk drive status indicato

Hard disk drive- status indicator pattern (RAID Only)ConditionBlinks green for three seconds, amber for three seconds, and turns off in six seconds.Re

NOTE: At least one EMM must be installed in the enclosure. If only one EMM is installed in the enclosure, it must be installed in the primary EMM bay