Dell Brocade Adapters Manual do Utilizador Página 178
- Página / 272
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
150 Brocade Adapters Installation and Reference Manual
53-1002144-01
Boot over SAN
4
7. When a message displays to insert the disk labeled manufacturer-supplied hardware support
disk, insert the Brocade adapter driver update disk that you created in step 3 and press Enter.
A list of devices displays.
8. Select Brocade's adapter from the list and press Enter.
The following message displays:
Setup will load support for the following mass storage device(s): Brocade Fibre Channel
Adapter.
9. Press Enter.
10. Remove the driver update disk after the driver update files load.
11. Continue responding to on-screen instructions and refer to your system documentation as
necessary to format and complete installation on the target boot LUN.
After Windows installs on the remote LUN, the system should automatically reboot from the
LUN.
Messages should display on the host system as BIOS or UEFI loads successfully. System boot
setup screens should also display a hard drive entry containing the Brocade adapter, boot LUN
number, and target storage device.
Installing Windows Server 2008 and the driver
Use the following steps to install Windows Server 2008 and the adapter driver on an unformatted
disk that you configured as a bootable device when setting up the adapter BIOS or UEFI on the host
system.
If the LUN you have targeted for booting over SAN already has an operating system installed, be
sure to use options for reformatting the LUN during Windows Server 2008 installation. Refer to your
operating system documentation for details.
NOTE
For HBAs and Fabric Adapter ports configured in HBA mode, you will need the fc dud file,
brocade_adapter_fc_<operating system>_<platform>_dud_<version>.zip. For CNAs and Fabric
Adapter ports configured in CNA mode, you will need the fcoe dud file,
brocade_adapter_fcoe_w2k8_x86_dud_<version>.zip>.
NOTE
For Microsoft Windows operating systems, the driver update disk does not verify prerequisite checks
as part of installation. Please review the operating system prerequisites and install the necessary
hotfixes after the operating system installation is complete.
1. Driver update disk files are provided for x86 and x64 systems. Refer to “Boot installation
packages” on page 49 for a list of driver update disk files and the operating systems that
support these files. Also refer to “Operating system support” on page 40 for information on
operating system support for adapter drivers.
2. Download the appropriate Windows 2008 adapter driver update disk (dud) .zip file for your
host platform from the Brocade adapters website
at www.brocade.com/adapters using the
following steps:
a.
On the adapters website, navigate to the drivers Downloads page.
b. On the downloads page, select your host’s operating system from the Download Individual
Software Installers, Drivers, or Documents list to access the appropriate downloads.
- Brocade Adapters 1
- Document History 2
- Contents 5
- Chapter 4 Boot Code 8
- Chapter 5 Specifications 8
- Appendix B MIB Reference 9
- Appendix C List of Acronyms 9
- 53-1002144-01 10
- About This Document 11
- Fabric Adapters 13
- Fabric OS and switch support 14
- Host operating system support 15
- Fibre Channel support 15
- FCoE support 16
- Ethernet support 16
- Hypervisor support 17
- What’s new in this document 18
- Document conventions 18
- Command syntax conventions 19
- Command examples 19
- Notes, cautions, and warnings 19
- Notice to the reader 20
- Additional information 20
- Other industry resources 21
- Providing details for support 22
- • The following BCU commands: 23
- Support Save overview 24
- VMware ESX systems 26
- Document feedback 27
- Product Overview 29
- AnyIO technology 30
- Changing the port mode 31
- Hardware compatibility 32
- Converged network adapters 33
- Stand-up adapters 34
- 1ASIC with heat sink 37
- 4Brocade serial number label 37
- PCI express connections 39
- Host bus adapters 40
- Stand-up models 41
- Mezzanine models 42
- Adapter features 44
- HBA 1 FC 45
- CNA 2 Ethernet and FCoE 45
- NIC 1 Ethernet 45
- FCoE features 48
- HBA features 55
- Adapter management features 59
- General adapter management 60
- Fabric Adapter management 61
- CNA management 61
- Ethernet management 62
- NIC Management 63
- HBA management 64
- Adapter software 65
- Management utilities 66
- Operating system support 68
- Host Connectivity Manager 70
- Boot code 70
- CIM Provider 71
- Adapter event messages 71
- Operating 72
- System and 72
- Platform 72
- Software installation options 76
- Boot installation packages 77
- (Platform) 80
- Using BCU commands 81
- Hardware Installation 83
- 1Mounting screw 86
- 3PCI X8 slot 86
- 4 Edge of host board 86
- 5SFP receivers 86
- Removing transceivers 87
- Replacing an adapter 88
- Brocade 1007 CNA 90
- Brocade 1741 CNA 90
- Updating PHY firmware 91
- Software Installation 93
- Installation notes 94
- Windows 2008 R2 96
- Using the GUI-based installer 97
- • Solaris systems 105
- - x_86 platforms 105
- Command options 106
- Important notes 107
- Installation examples 109
- • Linux systems 110
- • Windows systems 110
- • Linux and Solaris systems 113
- Downgrading driver only 116
- Installer log 117
- Installation Notes 119
- • INSTALL_OP= 120
- • Avoid checking for hot fix 123
- # vihostupdate -q 131
- Driver Verifier Manager 132
- Device Manager 132
- # modprobe -l bfa 133
- # modprobe -l bna 133
- Installing SNMP subagent 137
- Updating drivers with HCM 138
- HCM Agent operations 140
- HCM configuration data 142
- Backing up configuration data 143
- Restoring configuration data 143
- Boot Code 145
- Boot code updates 146
- Updating boot code with HCM 147
- Network boot 148
- Configuring network boot 151
- Boot over SAN 155
- Legacy BIOS parameters 157
- Disabling N_Port trunking 159
- Configuring boot over SAN 159
- Overview 160
- Note: Step numbers reference 161
- Procedures 162
- • Enable or disable BIOS 170
- Configuring UEFI 174
- ATTENTION 179
- #mk_initrd 191
- Using a LiveCD image 196
- Creating a WinPE image 197
- Specifications 199
- Hardware specifications 200
- Cabling 204
- Adapter LED operation 205
- TABLE 16 LED operation 206
- Converged Network Adapters 207
- Cabling (stand-up adapters) 211
- TABLE 21 LED operation 212
- Stand-up CNAs 213
- Mezzanine CNAs 214
- Host Bus Adapters 215
- TABLE 28 LED operation 219
- Regulatory compliance 220
- FCC warning (US only) 221
- VCCI statement (Japan) 222
- CE statement 222
- Canadian requirements 222
- Laser compliance 223
- Ё RoHS 224
- Mezzanine adapters 227
- Adapter Configuration 231
- • Linux - /etc/modprobe.conf 234
- Parameter Default Value Notes 235
- Network driver parameters 239
- NIC Teaming 242
- • TCP-UDP Checksum Offload 245
- • Interrupt Moderation 245
- • Number of 248
- • Heap values 248
- Configuring NetQueue 249
- MIB Reference 253
- In this appendix 254
- List of Acronyms 257
- Numerics 265
Manuais e produtos relacionados com Hardware de computador Dell Brocade Adapters
(176 páginas)
Hardware de computador Dell PowerVault 775N (Rackmount NAS Appliance) Manual do Utilizador
(96 páginas)
(96 páginas)
Hardware de computador Dell PowerVault 725N (Rackmount NAS Appliance) Manual do Utilizador
(172 páginas)
(172 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais