Dell Brocade Adapters Manual do Utilizador Página 103
- Página / 272
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Brocade Adapters Installation and Reference Manual 75
53-1002144-01
Using the Brocade Adapter Software Installer
3
FIGURE 16 Install Complete screen
12. Confirm that all software installed successfully. If the screen instructs you to restart or reboot
the system, select any options that apply.
13. Select Done.
14. Verify installation using tools available on your host system.
Refer to “Confirming driver package
installation”
on page 103 for details.
15. To make sure that the drivers and adapter boot code are synchronized, be sure to update your
adapter with the latest boot image from the Brocade website
at www.brocade.com/adapters
whenever you install or update adapter driver packages. From the adapters website, navigate
to the drivers Downloads page.
Access the appropriate download page by selecting your host’s
operating system from the Download Individual Software Installers, Drivers, or Documents list.
Refer to “Boot code updates” on page 118 for instructions to install the boot image.
NOTE
Installing management utilities on Windows systems creates a Brocade BCU shortcut on your
system desktop. Use this shortcut to launch the BCU> command prompt and enter BCU commands.
- Brocade Adapters 1
- Document History 2
- Contents 5
- Chapter 4 Boot Code 8
- Chapter 5 Specifications 8
- Appendix B MIB Reference 9
- Appendix C List of Acronyms 9
- 53-1002144-01 10
- About This Document 11
- Fabric Adapters 13
- Fabric OS and switch support 14
- Host operating system support 15
- Fibre Channel support 15
- FCoE support 16
- Ethernet support 16
- Hypervisor support 17
- What’s new in this document 18
- Document conventions 18
- Command syntax conventions 19
- Command examples 19
- Notes, cautions, and warnings 19
- Notice to the reader 20
- Additional information 20
- Other industry resources 21
- Providing details for support 22
- • The following BCU commands: 23
- Support Save overview 24
- VMware ESX systems 26
- Document feedback 27
- Product Overview 29
- AnyIO technology 30
- Changing the port mode 31
- Hardware compatibility 32
- Converged network adapters 33
- Stand-up adapters 34
- 1ASIC with heat sink 37
- 4Brocade serial number label 37
- PCI express connections 39
- Host bus adapters 40
- Stand-up models 41
- Mezzanine models 42
- Adapter features 44
- HBA 1 FC 45
- CNA 2 Ethernet and FCoE 45
- NIC 1 Ethernet 45
- FCoE features 48
- HBA features 55
- Adapter management features 59
- General adapter management 60
- Fabric Adapter management 61
- CNA management 61
- Ethernet management 62
- NIC Management 63
- HBA management 64
- Adapter software 65
- Management utilities 66
- Operating system support 68
- Host Connectivity Manager 70
- Boot code 70
- CIM Provider 71
- Adapter event messages 71
- Operating 72
- System and 72
- Platform 72
- Software installation options 76
- Boot installation packages 77
- (Platform) 80
- Using BCU commands 81
- Hardware Installation 83
- 1Mounting screw 86
- 3PCI X8 slot 86
- 4 Edge of host board 86
- 5SFP receivers 86
- Removing transceivers 87
- Replacing an adapter 88
- Brocade 1007 CNA 90
- Brocade 1741 CNA 90
- Updating PHY firmware 91
- Software Installation 93
- Installation notes 94
- Windows 2008 R2 96
- Using the GUI-based installer 97
- • Solaris systems 105
- - x_86 platforms 105
- Command options 106
- Important notes 107
- Installation examples 109
- • Linux systems 110
- • Windows systems 110
- • Linux and Solaris systems 113
- Downgrading driver only 116
- Installer log 117
- Installation Notes 119
- • INSTALL_OP= 120
- • Avoid checking for hot fix 123
- # vihostupdate -q 131
- Driver Verifier Manager 132
- Device Manager 132
- # modprobe -l bfa 133
- # modprobe -l bna 133
- Installing SNMP subagent 137
- Updating drivers with HCM 138
- HCM Agent operations 140
- HCM configuration data 142
- Backing up configuration data 143
- Restoring configuration data 143
- Boot Code 145
- Boot code updates 146
- Updating boot code with HCM 147
- Network boot 148
- Configuring network boot 151
- Boot over SAN 155
- Legacy BIOS parameters 157
- Disabling N_Port trunking 159
- Configuring boot over SAN 159
- Overview 160
- Note: Step numbers reference 161
- Procedures 162
- • Enable or disable BIOS 170
- Configuring UEFI 174
- ATTENTION 179
- #mk_initrd 191
- Using a LiveCD image 196
- Creating a WinPE image 197
- Specifications 199
- Hardware specifications 200
- Cabling 204
- Adapter LED operation 205
- TABLE 16 LED operation 206
- Converged Network Adapters 207
- Cabling (stand-up adapters) 211
- TABLE 21 LED operation 212
- Stand-up CNAs 213
- Mezzanine CNAs 214
- Host Bus Adapters 215
- TABLE 28 LED operation 219
- Regulatory compliance 220
- FCC warning (US only) 221
- VCCI statement (Japan) 222
- CE statement 222
- Canadian requirements 222
- Laser compliance 223
- Ё RoHS 224
- Mezzanine adapters 227
- Adapter Configuration 231
- • Linux - /etc/modprobe.conf 234
- Parameter Default Value Notes 235
- Network driver parameters 239
- NIC Teaming 242
- • TCP-UDP Checksum Offload 245
- • Interrupt Moderation 245
- • Number of 248
- • Heap values 248
- Configuring NetQueue 249
- MIB Reference 253
- In this appendix 254
- List of Acronyms 257
- Numerics 265
Manuais e produtos relacionados com Hardware de computador Dell Brocade Adapters
(176 páginas)
Hardware de computador Dell PowerVault 775N (Rackmount NAS Appliance) Manual do Utilizador
(96 páginas)
(96 páginas)
Hardware de computador Dell PowerVault 725N (Rackmount NAS Appliance) Manual do Utilizador
(172 páginas)
(172 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais