Dell PowerEdge M IO Aggregator Manual do Utilizador

Users’ Guide for the Programmable MUX (PMUX) on the M I/O Aggregator Dell Networking OS version 9.3(0.0)

Uplink Failure Detection (UFD) UFD provides detection of the upstream connectivity loss and, if used with network interface controller (NIC) teaming,

NOTE: In this example, if port-channel 128 goes down, the downstream interfaces are brought operationally down (set to UFD error-disabled). Similarly

4. Initialize the port-channel with configurations such as admin up, portmode, and switchport. Dell#configure Dell(conf)#int port-channel 128 Dell(c

T Te 0/1 12 Active T Po128(Te 0/41-42) T

2. Configure the VLT domain. Dell#configure Dell(conf)#vlt domain 1 Dell(conf-vlt-domain)# peer-link port-channel 127 -> VLT peer destination Del

Dell# 5. Configure the secondary VLT. NOTE: Repeat steps from 1 through 4 on the secondary VLT, ensuring you use the different backup destination a

1. Configure stack groups on all stack units. Dell# Dell#configure Dell(conf)#stack-unit 0 stack-group 0 Dell(conf)#00:37:46: %STKUNIT0-M:CP %IFMGR-

N-Port Identifier Virtualization (NPIV) Proxy Gateway (NPG) NPIV NPG feature provides Fibre Channel over Ethernet (FCoE)-FC bridging on the IOA and M

Related Commands • fcoe-map • show fcoe-map fabric Apply an FCoE map on a fabric-facing Fibre Channel (FC) port. Syntax Fabric map-name Parameters

Related Commands • fcoe-map • show fcoe-map fcf-priority Configure the priority to select an upstream FCoE forwarder (FCF). Syntax fcf—priority pri

Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual pr

Parameters priority-bitmap = Enter the priority-bitmap range. The range is from 1 to FF. Defaults 0x8 Command Modes PROTOCOL LLDP Command History Vers

Defaults 8 seconds Command Modes FCOE MAP Command History Version 9.3(0.0) Related Commands • fcoe-map • show fcoe-map interface vlan Create a dedi

Priority-pgid Assign 802.1 priority traffic to a priority group in a DCB map. Syntax priority-pgid dot1p0_group-num dot1p1_group-num dot1p2_group-num

priority group. The range is 1 to 100. The sum of all allocated bandwidth percentages in priority groups in a DCB map must be 100%. • strict-priority

• EXEC Privilege Command History Version 9.3(0.0) Usage Information Use this command to display the FC and FCoE parameters used to configure server-f

Active (all mandatory FCoE and FC parameters are correctly configured) Incomplete (either the FC-MAP value, fabric ID, or VLAN ID are not correctly co

show npiv devices Display the FCoE and FC devices currently logged in to an IOA and MXL switch with the FC Flex IO module NPIV proxy gateway. Syntax s

ENode WWPN : 10:00:00:00:c9:d9:9c:cb ENode WWNN : 10:00:00:00:c9:d9:9c:cd FCoE MAC : 0e:fc:03:01:02:02 FC-ID : 01:02:01 LoginMethod : FDISC

FCoE VLAN ID of the dedicated VLAN used to transmit FCoE traffic from a server CNA to a fabric and configured on both the server-facing IOA and MXL sw

Enabling Fibre Channel Capability on the Switch You must first enable an IOA and MXL switch with the FC Flex IO module that you want to configure as

Introduction This document provides configuration instructions and examples for the Programmable MUX (PMUX mode) for the Dell Networking M I/O Aggreg

Important Points to Remember • If you remove a dot1p priority-to-priority group mapping from a DCB map (the no priority pgid command), the PFC and E

to transmit FCoE traffic. Creating an FCoE Map The values for the FCoE VLAN, fabric ID, and FC-MAP must be unique. Apply an FCoE map on downstream s

The default is 8 seconds. Applying an FCoE Map on Server-Facing Ethernet Ports You can apply multiple FCoE maps on an Ethernet port or port channel.

Task Command Command Mode Configure a fabric-facing FC port. interface fibrechannel slot/port CONFIGURATION Apply the FCoE and FC fabric configuratio

3. Create the dedicated VLAN to be used for FCoE traffic. Dell(conf)#interface vlan 1002 4. Configure an FCoE map to be applied to the downstream

For more information about NPIV Proxy Gateway information, refer to the 9.3(0.0) Addendum. IOA PMUX Mode CLI Commands The following tables list the

iscsi target port Interfaces CLI Commands clear counters interface flowcontrol interface range interface ManagementEthernet mtu interface vlan portm

percentage clear qos statistics description policy-aggregate policy-map-output qos-policy-output rate police rate shape service-policy output service-

Unit Boot-Mode Next-Boot ------------------------------------------------ 0 standalone standalone Dell# 2. Change IOA mode to PMUX mode. Dell(conf)

Multiple Uplink LAGs Unlike IOA Automated modes (Standalone, VLT, and Stacking Modes), the IOA Programmable MUX can support multiple uplink LAGs. You

4. Configure the port mode, VLAN, and so forth on the port-channel. Dell#configure Dell(conf)#int port-channel 10 Dell(conf-if-po-10)#portmode hybri

Te 0/41 Up 0 Te 0/42 Up 0 LAG bundle - 11 Utilization[In Percent] - 0 Alarm State - I

Please save and reset unit 0 for the changes to take effect. Dell(conf)# 2. Save the configuration. Dell#write memory ! 01:05:48: %STKUNIT0-M:CP %FI

5. Show the port channel status. Dell#sh int port-channel br Codes: L - LACP Port-channel O - OpenFlow Controller Port-channel LAG Mode