Dell OptiPlex 380 Especificações Página 1

Dell™OptiPlex™380ServiceManual—Desktop  Notes, Cautions, and Warnings IfyoupurchasedaDell™nSeriescomputer,anyreferencesinthisdocumen

Replacing the Cover To replace the cover, perform the above steps in reverse order. Back to Contents Page

Back to Contents Page Diagnostics Dell™OptiPlex™380ServiceManual—Desktop Dell Diagnostics Power Button Light Codes Beep Codes Diagnostic

2. If a problem is encountered during a test, a message appears with an error code and a description of the problem. Write down the error code and pro

Diagnostic Lights To help troubleshoot a problem, your computer has four lights labeled 1, 2, 3, and 4 on the bank panel. When the computer starts no

Back to Contents Page l  If the operating system is attempting to boot from a device (such as the floppy drive or optical drive), check system setup

Back to Contents Page Expansion Cards Dell™OptiPlex™380ServiceManual—Desktop Removing Expansion Cards 1. Follow the procedures in Before Working

Back to Contents Page Fan Dell™OptiPlex™380ServiceManual—Desktop Removing the Fan 1. Follow the procedures in Before Working Inside Your Compute

4. Lift the fan and remove it from the computer. Replacing the Fan To replace the fan, perform the above steps in reverse order. Back to Contents Pa

Back to Contents Page Hard Drive Dell™OptiPlex™380ServiceManual—Desktop Removing the Hard Drive 1. Follow the procedures in Before Working Insid

5. Press in on the blue securing tabs on each side of the hard drive, and then slide the hard drive towards the back of the computer. 6. Lift the ha

Back to Contents Page System Setup Dell™OptiPlex™380ServiceManual—Desktop Boot Menu Navigation Keystrokes Entering System Setup System Se

Replacing the Hard Drive To replace the hard drive, perform the above steps in reverse order. Back to Contents Page

Back to Contents Page Heat Sink and Processor Dell™OptiPlex™380ServiceManual—Desktop Removing the Heat Sink and Processor 1. Follow the procedur

4. Lift the heat sink and remove it from the computer. 5. Slide the release lever from under the center-cover latch and rotate the release lever upw

6. Lift the processor cover. 7. Remove the processor from the computer.

Replacing the Heat Sink and Processor To replace the heat sink and processor, perform the above steps in reverse order. Back to Contents Page CAUTION

Back to Contents Page I/O Panel Dell™OptiPlex™380ServiceManual—Desktop Removing the I/O Panel 1. Follow the procedures in Before Working Inside

4. Rotate the I/O panel away from the edge of the computer and remove it from the computer. Replacing the I/O Panel To replace the I/O panel, perfor

Back to Contents Page Memory Dell™OptiPlex™380ServiceManual—Desktop Removing the Memory Module(s) 1. Follow the procedures in Before Working Ins

Replacing the Memory Module(s) To replace the memory module(s), perform the above steps in reverse order. Back to Contents Page

Back to Contents Page Optical Drive Dell™OptiPlex™380ServiceManual—Desktop Removing the Optical Drive 1. Follow the procedures in Before Working

 Date/Time Displays the system date and time. Changes to the system date and time take effect immediately. Boot Sequence Specifies the order in which

4. Lift the drive-release latch and slide the drive towards the back of the computer. 5. Lift the optical drive up and away from the computer.

Replacing the Optical Drive To replace the optical drive, perform the steps above in reverse order. Back to Contents Page

Back to Contents Page Removing and Replacing Parts Dell™OptiPlex™380ServiceManual—Desktop Back to Contents Page Cover Hard Drive Riser As

Back to Contents Page Power Supply Dell™OptiPlex™380ServiceManual—Desktop Removing the Power Supply 1. Follow the procedures in Before Working In

7. Release the processor power connector cable from their routing guides under the system board. 8. Remove the screws that secure the power supply t

9. Press the power-supply release latch at the bottom of the chassis and then slide the power supply towards the front of the computer. 10. Lift the

Replacing the Power Supply To replace the power supply, perform the above steps in reverse order. Back to Contents Page

Back to Contents Page Riser Assembly Dell™OptiPlex™380ServiceManual—Desktop Removing the Riser Assembly 1. Follow the procedures in Before Workin

4. Pull up on the riser-assembly, and lift the riser assembly up and away from the computer. 5. Rotate the card retention latch upwards.

6. Pull the card release latch on the riser board away from the card and ease the card out of its connector. Replacing the Riser Assembly To replace

l Auto (default) l COM2 l COM4 The Operating System may allocate resources even though the setting is disabled. Miscellaneous Devices Enables or disab

Back to Contents Page Secondary Hard Drive (Optional) Dell™OptiPlex™380ServiceManual—Desktop Removing the Secondary Hard Drive (Optional) 1. Fol

5. Pull up on the release latch, and then slide the hard drive towards the back of the computer. 6. Lift the hard drive and remove it from the compu

Replacing the Secondary Hard Drive (Optional) To replace the secondary hard drive, perform the above steps in reverse order. Back to Contents Page

Back to Contents Page Specifications Dell™OptiPlex™380ServiceManual—Desktop System Information Memory Audio Expansion Bus 

Express x1): Mini-tower one Desktop one (with combo riser installed) Small form factor none oneDrives Externally accessible:  5.25-inch driv

Back to Contents Page  Physical Height Width Depth Weight Mini-Tower 40.8 cm (16.1 inches) 18.7 cm (7.4 inches) 43.3 cm (17.0 inches) 12.0 kg (26

Back to Contents Page Standard Back Plate Dell™OptiPlex™380ServiceManual—Desktop Removing the Standard Back Plate 1. Follow the procedures in Be

Back to Contents Page System Board Layout Dell™OptiPlex™380ServiceManual—Desktop Back to Contents Page 1speaker connector (INT_SPKR)2processo

Back to Contents Page System Board Dell™OptiPlex™380ServiceManual—Desktop Removing the System Board 1. Follow the procedures in Before Working I

8. Disconnect the IO-panel cable from the system board. 9. Disconnect the optical-drive data cable from the system board.

CPU XD Support Enables or disables the execute disable mode of the processor. This option is enabled by default. Computrace(R) Enables or disables the

10. Disconnect the hard-drive data cable from the system board. 11. Disconnect the processor power cable from the system board. 12. Remove the screw

13. Remove the heat-sink assembly bracket from the computer. 14. To remove the system board, slide the system board towards the back of the computer

Replacing the System Board To replace the system board, perform the above the steps in reverse order. Back to Contents Page

Back to Contents Page Working on Your Computer Dell™OptiPlex™380ServiceManual—Desktop Before Working Inside Your Computer Use the following safe

Click Start® Turn Off Computer® Turn Off. The computer turns off after the operating system shutdown process is complete. 2. Ensure that the comput

Back to Contents Page The default IP port is 06910. Client DHCP Specifies how the client obtains the IP address. l Static IP l DHCP (default) Client

Back to Contents Page Coin-Cell Battery Dell™OptiPlex™380ServiceManual—Desktop Removing the Coin-Cell Battery 1. Follow the procedures in Before

Replacing the Coin-Cell Battery To replace the coin-cell battery, perform the above steps in reverse order. Back to Contents Page

Back to Contents Page Cover Dell™OptiPlex™380ServiceManual—Desktop Removing the Cover 1. Follow the procedures in Before Working Inside Your Com