Dell OptiPlex GX260 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Computadores Dell OptiPlex GX260. Dell OptiPlex GX260 User Manual Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 100
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 0
Dell™ OptiPlex™ GX260 Service Manual
Before You Begin
Computer Cover
Inside Your Computer
Badge
Battery
Chassis Intrusion Switch
Control Panel
Cards and Adapters
Drives
Front-Panel Inserts
I/O Panel
Memory
Microprocessor
Power Supply
System Board
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Information in this document is subject to change without notice.
© 2003 Dell Computer Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and OptiPlex are trademarks of Dell Computer Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
March 2003 Rev. A02
Vista de página 0
1 2 3 4 5 6 ... 99 100

Resumo do Conteúdo

Página 1

Dell™ OptiPlex™ GX260 Service ManualBefore You BeginComputer CoverInside Your ComputerBadgeBatteryChassis Intrusion SwitchControl PanelCards and Adapt

Página 2 - Before You Begin

1 CD/DVD drive data cable 6 IDE data cable (hard drive)2 floppy-drive data cable 7 input/output cable3 control-panel cable 8 input/output audio cable4

Página 3

1 card-clip lever 3 slot connector2 card clip 4 card slotInstalling an AGP/DVI Adapter Card1. To add or replace the card, gently press it down into t

Página 4 - Computer Cover

1 CD/DVD drive audio cable 5 input/output cable2 CD/DVD drive data cable 6 input/output audio cable3 floppy-drive data cable 7 IDE data cable (hard dr

Página 5

1 CD/DVD drive power cable 6 IDE drive power cable (hard drive)2 CD/DVD drive data cable 7 IDE drive data cable (hard drive)3 CD/DVD drive audio cable

Página 6 - Closing the Computer Cover

Back to Contents PageBadgeDell™ OptiPlex™ GX260 Service Manual Removing the Badge Replacing the Badge Small Desktop and Small Mini-Tower ComputersR

Página 7 - Inside Your Computer

1. Open the front USB door. 2. From inside the door, push in the two tabs on either side of the badge to release the badge. 3. Press the badge unti

Página 8

1 accent door2 front mask2. Replace the badge by pressing it into place, ensuring that the two tabs click, securing it into position. Small Desktop a

Página 9 - Computer Cables

Back to Contents PageBatteryDell™ OptiPlex™ GX260 Service ManualReplacing the BatteryCAUTION: A new battery can explode if it is incorrectly installed

Página 11 - Small Mini-Tower Computer

Back to Contents PageChassis Intrusion SwitchDell™ OptiPlex™ GX260 Service Manual Removing the Chassis Intrusion Switch Replacing the Chassis Intrus

Página 12

Small Mini-Tower Computer1. Disconnect the chassis intrusion switch cable connector from the control panel on the front of the chassis. Note the rout

Página 13 - Removing the Badge

Back to Contents PageBefore You BeginDell™ OptiPlex™ GX260 Service Manual Getting Started Recommended Tools Precautionary Measures Protecting Agai

Página 14 - Replacing the Badge

2. Slide the chassis intrusion switch out of its slot and remove the switch and its attached cable from the chassis. Replacing the Chassis Intrusion

Página 15

Back to Contents PageControl PanelDell™ OptiPlex™ GX260 Service Manual Removing the Control Panel Replacing the Control PanelCAUTION: Before you per

Página 16 - Replacing the Battery

1 tabs (2 on each side)2 computer3 computer cover1 metal control-panel shield2 screw2. Remove the metal control-panel shield.

Página 17

3. Remove the screw that holds the control panel to the computer, and remove the control panel. Small Desktop Computer1. Remove the front I/O panel.

Página 18 - Chassis Intrusion Switch

1 computer cover tab (remove the CD drive to access this tab)2 top-panel tabs3 top panel4 bottom panel5 computer cover screw6 computer cover tabs (2)2

Página 19

Replacing the Control PanelSmall Form-Factor Computer1. Replace the control panel and the control-panel shield. 2. Replace the computer cover. Ensur

Página 20

1 accent door2 front mask3. Replace the computer cover and ensure that the two metal hooks and tabs are securely in position.

Página 21 - Control Panel

1 metal hooks (2)4. To replace the front mask and accent door, press them into position. Small Desktop ComputerFollow the steps in the "Removing

Página 22

Back to Contents PageCards and AdaptersDell™ OptiPlex™ GX260 Service Manual Small Form-Factor Computer Small Desktop Computer Small Mini-Tower Comp

Página 23

1 edge connector2 card3 retention arm4 card connector5 filler bracket3. If you are installing a new card, remove the filler bracket to create an empt

Página 24

that might harm internal components.4. Disconnect your computer and devices from their power sources. Also, disconnect any telephone or telecommunica

Página 25 - Replacing the Control Panel

1 bracket caught outside of slot2 bracket within slot3 fully seated card4 not fully seated card7. Before you lower the retention arm, ensure that: Th

Página 26 - 2 front mask

1 alignment guide2 alignment bar3 retention arm4 filler bracketNOTICE: Do not route card cables over or behind the cards. Cables routed over the cards

Página 27

Serial Port AdaptersInstalling a Serial Port AdapterCAUTION: Before you perform this procedure, see "Precautionary Measures."1. Lift the ta

Página 28 - Cards and Adapters

5. Lower the retention arm into place, securing the card(s) in the computer (see "Closing the Retention Arm"). Removing a Serial Port Adapt

Página 29 - Card Connection

Removing the Card1 card notch2 card-clip lever3 card-clip tab4 card clip5 card slotInstalling an AGP or DVI Adapter Card1. To add or replace the card

Página 30 - Closing the Retention Arm

Back to Contents PageDrivesDell™ OptiPlex™ GX260 Service Manual Small Form-Factor Computer Small Desktop Computer Small Mini-Tower ComputerSmall Fo

Página 31 - Removing a PCI Card

2 hard-drive cable2. Press in on the tabs on each side of the drive, slide the drive toward the I/O panel, and remove it from the computer. Removing

Página 32 - Serial Port Adapters

3. Install the hard drive into the computer by gently sliding the drive into place until you hear it securely click. NOTICE: Match the colored strip

Página 33 - AGP and DVI Adapter Cards

Floppy DriveCAUTION: Before you perform this procedure, see "Precautionary Measures."Removing a Floppy Drive1. Disconnect the floppy-drive

Página 34 - Removing the Card

2 tab3 interposer board4 system board floppy-drive connector (DSKT)b. To release the floppy-drive cable from the connector, slide the lever until it

Página 35 - Small Form-Factor Computer

Back to Contents PageComputer CoverDell™ OptiPlex™ GX260 Service Manual Opening the Computer Cover Closing the Computer CoverOpening the Computer Co

Página 36 - Installing a Hard Drive

out of the sled. Removing the Floppy Drive1 sled tab2 sledInstalling a Floppy Drive1. Snap the replacement drive into the sled and ensure that it is

Página 37 - Front-Panel Inserts

1 connector notch2 interposer board alignment hole3 floppy-drive cable4 lever4. Attach the power cable to the interposer board on the floppy drive. 5

Página 38 - Floppy Drive

CD/DVD DriveCAUTION: Before you perform this procedure, see "Precautionary Measures."Removing a CD/DVD Drive1. Disconnect the power and aud

Página 39

Installing a CD/DVD Drive1. Unpack the drive and prepare it for installation. Check the documentation that accompanied the drive to verify that the d

Página 40 - Installing a Floppy Drive

1 interposer board2 notch on inside of cover3 interposer board tabIf your computer came with an IDE CD drive, use the spare connector on the existing

Página 41

Small Desktop Computer Hard Drive Front-Panel Inserts Floppy Drive CD/DVD DriveHard DriveCAUTION: Before you perform this procedure, see "Pre

Página 42 - CD/DVD Drive

1 hard-drive cable2 power cable3. Press in on the tabs on each side of the drive and slide the drive up and out. Removing the Hard Drive1 tabs (2)2 h

Página 43 - Installing a CD/DVD Drive

1. Check the documentation for the drive to verify that it is configured for your computer. NOTICE: To avoid damage to the drive, do not set it on a

Página 44

If you are installing a new floppy or CD/DVD drive rather than replacing a drive, remove the front-panel inserts:1. Facing the front of the computer,

Página 45

2. Disconnect the power and floppy-drive cables from the back of the floppy drive. 3. Disconnect the floppy-drive cable from the system board connec

Página 46

1 security cable slot2 padlock ring3 release buttons (one on each side)Small Mini-Tower Computer1 release buttons2 security cable slot3 padlock ring1.

Página 47

Installing a Floppy Drive1. If the replacement drive does not have the bracket rails attached, see step 2 in the previous section for instructions on

Página 48

3 floppy-drive connector (DSKT)5. Reconnect the power and data cables to the back of the drive installed in the CD/DVD drive bay located above theflo

Página 49 - Floppy Drive Removal

bay. Installing a CD/DVD Drive1. Unpack the drive and prepare it for installation. Check the documentation that accompanied the drive to verify that

Página 50

1 audio cable2 power cable3 CD/DVD drive cable4 IDE2 connector6. If you are installing a drive that has its own controller card, install the controll

Página 51

Removing a Hard Drive1. Disconnect the power and hard-drive cables from the drive. Removing Power and Drive Cables1 power cable2 hard-drive cable2.

Página 52

Installing a Hard Drive1. Unpack the replacement hard drive, and prepare it for installation. 2. Check the documentation for the drive to verify tha

Página 53

Ensure that the rail tabs are positioned at the back of the hard drive.NOTICE: Do not install any drive into the lower hard-drive bay until you have r

Página 54 - Removing a Hard Drive

1 power cable2 second hard-drive cable (secondary drive)3 first hard-drive cable (primary boot drive)Front-Panel InsertsIf you are installing a new fl

Página 55 - Adding a Second Hard Drive

2. Press the insert until it pops free of the front-panel cover. Removing the Front-Panel InsertsFloppy DriveCAUTION: Before you perform this procedu

Página 56 - Attaching Cables

1. Disconnect the power and floppy-drive cables from the back of the floppy drive. 2. Disconnect the other end of the floppy-drive cable from the sy

Página 57

NOTICE: Ensure that sufficient space exists to support the open cover—at least 30 cm (1 ft) of desktop space.NOTICE: Open the computer cover slowly to

Página 58

Installing a Floppy Drive1. If the replacement drive does not have the bracket rails attached, see step 2 in the previous section for instructions on

Página 59

1 power cable2 audio cable3 CD/DVD drive cable2. Press inward on the two tabs on the sides of the drive, and then slide the drive upward and remove i

Página 60

1. If you are installing a new drive, unpack the drive and prepare it for installation. Check the documentation that accompanied the drive to verify

Página 61

Back to Contents PageFront-Panel InsertsDell™ OptiPlex™ GX260 Service Manual Removing Front-Panel Inserts Replacing Front-Panel InsertsRemoving Fron

Página 62

Small Mini-Tower Computer

Página 63

Replacing Front-Panel InsertsTo replace a front-panel insert, follow the appropriate procedure, in reverse, in "Removing Front-Panel Inserts.&quo

Página 64

Back to Contents PageI/O PanelDell™ OptiPlex™ GX260 Service Manual Removing the I/O Panel Replacing the I/O PanelRemoving the I/O PanelSmall Form-Fa

Página 65 - Replacing Front-Panel Inserts

4. From inside the computer cover, remove the mounting screw that secures the I/O panel to the computer. 5. Remove the I/O panel from the computer.

Página 66 - I/O Panel

7. Remove all cables that are connected to the I/O panel. 8. Remove the mounting screw that secures the I/O panel to the computer. 9. Remove the I/

Página 67

4. Remove the I/O panel from the chassis. Replacing the I/O PanelTo replace the I/O panel, follow the removal procedures in reverse.Back to Contents

Página 68

Back to Contents PageInside Your ComputerDell™ OptiPlex™ GX260 Service Manual Key Components Computer CablesKey ComponentsNOTE: User service access

Página 69 - Replacing the I/O Panel

Back to Contents PageMemoryDell™ OptiPlex™ GX260 Service Manual Removing a Memory Module Adding a Memory ModuleRemoving a Memory ModuleCAUTION: Use

Página 70 - Adding a Memory Module

4 notch5 securing clips (2)6 memory connectors on system board2. Align the notch on the bottom of the module with the crossbar in the connector. NOTI

Página 71

Back to Contents PageMicroprocessorDell™ OptiPlex™ GX260 Service ManualRemoving and Installing the Heat-Sink Assembly and Microprocessor Small Form-F

Página 72 - Microprocessor

1 blower 4 retention base2 screws (2) 5 heat sink3 lever4. Lift the heat sink/blower assembly away from the microprocessor. 5. Remove the two screws

Página 73 - Microprocessor Installation

1 pin-1 corners of microprocessor and socket alignedNOTICE: You must position the microprocessor correctly in the socket to avoid permanent damage to

Página 74

1 heat sink/blower assembly2 lever3 retention base15. Plug the fan cable into the FAN connector on the system board. 16. Plug the 12-volt power cabl

Página 75

4. Remove the heat sink. a. Press and lower the green lever on the retention mechanism until it is parallel to the system board. b. Gently rock the

Página 76 - Heat Sink Removal

1 heat sink2 lever3 retention baseNOTICE: Lay the heat sink down with the thermal solution facing upward.NOTICE: If you are installing a microprocesso

Página 77

1 release lever2 microprocessor3 socket6. Remove the microprocessor from the socket. Leave the release lever extended in the release position so that

Página 78

1 pin-1 corners of microprocessor and socket alignedNOTICE: Microprocessor pins are delicate. To avoid damage, ensure that the microprocessor aligns p

Página 79 - Heat Sink Replacement

1 hard drive 6 padlock ring2 internal speaker 7 heat sink and blower assembly3 chassis intrusion switch 8 system board4 card cage 9 floppy drive5 powe

Página 80 - Back to Contents Page

15. Reconnect the 12-volt power cable to the 12VPOWER connector on the system board. Back to Contents Page

Página 81 - Power Supply

Back to Contents PagePower SupplyDell™ OptiPlex™ GX260 Service Manual Removing the Power Supply Replacing the Power SupplyRemoving the Power SupplyS

Página 82

1 release button2 AC power connectorSmall Mini-Tower Computer1. Disconnect the AC power cable from the back of the power supply. 2. Disconnect the D

Página 83 - Replacing the Power Supply

pinched or crimped.3. On the small desktop computer, remove the expansion-card cage and remove the power cables from the side of thehard drive. To re

Página 84 - System Board

Back to Contents PageSystem BoardDell™ OptiPlex™ GX260 Service Manual System Board Components Removing the System Board Replacing the System BoardS

Página 85 - Removing the System Board

6 front-panel connector (FRONTPANEL) 17 memory module connectors (DIMM A and DIMM B)7 PCI riser (small mini-tower computer only) 18 microprocessor fan

Página 86 - Replacing the System Board

Removing the System Board5. Place the system board that you just removed next to the replacement system board. Replacing the System Board1. Transfer

Página 88

Back to Contents PageSmall Desktop ComputerDell™ OptiPlex™ GX260 Service Manual PCI Cards Serial Port Adapters AGP and DVI Adapter CardsNOTE: Befor

Página 89 - Installing a Card

1 lever 5 card-edge connector2 retention arm 6 card connector3 filler bracket 7 riser board4 card 8 card cageInstalling a Card1. If you are installin

Página 90

1 hard drive 6 heat sink and blower assembly2 internal speaker 7 power supply3 chassis intrusion switch 8 floppy drive4 system board 9 CD/DVD drive5 p

Página 91

b. Make sure that the riser board is fully seated in the connector on the system board. Replacing the Card Cage1 card cage2 tabs3 slots6. Reconnect

Página 92

1 retention arm2 filler bracket3 adapter bracket4. Slide the adapter bracket down over the card-slot opening, and lower the retention arm, securing t

Página 93

1 card cage2 serial adapter cable3 serial adapter system board connector (SER2)Removing a Serial Port AdapterCAUTION: Before you perform this procedur

Página 94

1 hinged lever2 indented tab (side view)2. Press the card-clip lever toward the card slot and remove the installed card. Removing the Card1 card notc

Página 95

Installing an AGP or DVI Adapter Card1. To add or replace the card, press the card-clip lever toward the card slot and gently press the card into the

Página 96

Back to Contents PageSmall Mini-Tower ComputerDell™ OptiPlex™ GX260 Service Manual PCI Cards Serial Port Adapters AGP and DVI Adapter CardsNOTE: Be

Página 97

2. If you are installing a new card, remove the filler bracket to create a card-slot opening, then continue with step 4. 3. If you are replacing a c

Página 98

1 filler bracket2 alignment bar3 alignment guide4 retention armNOTICE: Do not route card cables over or behind the cards. Cables routed over the cards

Página 99

Serial Port AdaptersInstalling a Serial Port AdapterCAUTION: Before you perform this procedure, see "Precautionary Measures."1. If you are

Página 100

3 serial adapter cable4 retention arm5. Attach the serial adapter cable to the serial port connector on the system board (labeled SER2). AGP and DVI

Comentários a estes Manuais

Sem comentários